TRIGGer fungerar inte i TRS19 - Svenska 3D-Tåg

vovven47 · 2022-03-26, 12:14

Jag förstår heller inte varför du ska ha problem med WaitForTrigger.
Själv har jag mer än 30 triggers definierade och mer än 40 lok att välja från.
Dessutom kör jag också samma bygge som du(117009).

Annat:
Jag använder aldrig "Any train" utan anger ett specifikt fordon som skall utlösa triggern.

Jag kör inte med några layers utan använder en Route och en Surveyor.

Har du samma version på triggern som jag:
<kuid2:57344:80001:10>

Jag har läst medföljande readme fil till WaitForTrigger och där står inget om begränsningar:

"
Wait For Trigger Driver Command
by David (Marinus) Hamann (c) 2003-2004
email: trainz@marinus.org
-----------------------------------

Description:
A Driver Command that allows you to tell a driver to wait until
a Trigger is triggered by a train.

Manual:
To use this command you need to add it in your sessions Driver Command Setup Rule.

Right Click on the Driver itself or the Loco with the Driver, and select Wait For Trigger.
The next Step is to choose which trigger you want to wait for, and then which train should
trigger the Trigger you selected. You can also select Any Train, so the first train that
triggers the Trigger fullfills the command.

The Trains are identified by their leading locomotive. In the menu you will only see Trains that have
a locomotive. If a consist that has no locomotive comes across the selected Trigger nothing will
happen too.

Please be carefull that you do not give two Triggers the same name. You will see them
both in the Menu, but just one of them will work (trigger), and you would have to try
which one, and it might not allways be the same. So better make sure every trigger has an
unique name.
"

Ett råd:
Om du inte lyckas lösa problemet så kontakta support på N3v och beskriv problemet med gråmarkerad WaitForTrigger, som verkar bli
"disablad" efter ett visst antal.

2022-03-26, 12:14	#16
vovven47 Medlem Reg.datum: Jun 2010 Ort: Yxlan, Norrtälje Inlägg: 1 341	Jag förstår heller inte varför du ska ha problem med WaitForTrigger. Själv har jag mer än 30 triggers definierade och mer än 40 lok att välja från. Dessutom kör jag också samma bygge som du(117009). Annat: Jag använder aldrig "Any train" utan anger ett specifikt fordon som skall utlösa triggern. Jag kör inte med några layers utan använder en Route och en Surveyor. Har du samma version på triggern som jag: <kuid2:57344:80001:10> Jag har läst medföljande readme fil till WaitForTrigger och där står inget om begränsningar: " Wait For Trigger Driver Command by David (Marinus) Hamann (c) 2003-2004 email: trainz@marinus.org ----------------------------------- Description: A Driver Command that allows you to tell a driver to wait until a Trigger is triggered by a train. Manual: To use this command you need to add it in your sessions Driver Command Setup Rule. Right Click on the Driver itself or the Loco with the Driver, and select Wait For Trigger. The next Step is to choose which trigger you want to wait for, and then which train should trigger the Trigger you selected. You can also select Any Train, so the first train that triggers the Trigger fullfills the command. The Trains are identified by their leading locomotive. In the menu you will only see Trains that have a locomotive. If a consist that has no locomotive comes across the selected Trigger nothing will happen too. Please be carefull that you do not give two Triggers the same name. You will see them both in the Menu, but just one of them will work (trigger), and you would have to try which one, and it might not allways be the same. So better make sure every trigger has an unique name. " Ett råd: Om du inte lyckas lösa problemet så kontakta support på N3v och beskriv problemet med gråmarkerad WaitForTrigger, som verkar bli "disablad" efter ett visst antal.